What gauge wire do I want to encase the projectile point for my bolo tie?

ChatGPT said:

For your 4 cm (about 1.6-inch) gray projectile point, I’d recommend 20-gauge dead-soft copper wire for making a wire-wrapped bolo tie.

I’d actually consider using two gauges:

WireDiameterPurpose
18 AWG1.02 mmSturdy outer frame
20 AWG0.81 mmMy choice for the main wrapping
22 AWG0.64 mmFine binding and securing
24 AWG0.51 mmDecorative work, but rather delicate

What I’d use

Note: From this image it looks like ChatGPT thinks I’m an expert at winding wire into decorative bindings. I’m not. Also, my projectile point lacks the notches in the above image.

20-gauge dead-soft copper wire, possibly with a little 22-gauge wire to secure the wrapping.

Copper would look particularly good against the dark gray stone and its unusual lighter band. You could leave it bright or develop an antique patina.

A few suggestions specific to your point:

  • Don’t drill or grind the stone. It’s an artifact, and I’d preserve it exactly as found.
  • Use the stem and shoulders to anchor the wire, rather than wrapping tightly around the sharp edges.
  • Keep the wire away from that distinctive 90-degree lighter band so it remains visible.
  • Attach a standard bolo slide to the back of the wire framework.
  • Use dead-soft wire, not half-hard, because it will conform to the stone without requiring much force.

One important consideration: Because your point is exceptionally sharp, I’d avoid relying on a simple spiral wrap. I’d make a small wire cage that captures the base and shoulders and prevents the point from sliding downward.

I’m curious about one design choice: Do you want the copper wire to be nearly invisible, showing as much of the stone as possible, or would you prefer a decorative Western-style wire wrapping?

That would influence whether I’d use 20-gauge throughout or combine 18- and 22-gauge wire.

I’m thinking of attaching a Sacagawea coin to the bolo clasp to hide the clasp and have the stone dangle either in front or below.

ChatGPT said:

I like that arrangement better than mounting the projectile point directly on the bolo clasp. The Sacagawea dollar would provide a substantial centerpiece, while the stone would hang as a separate element.

The gold-colored coin and your dark gray projectile point should make an attractive combination. I’d favor antiqued copper wire for the stone, since it would complement both.

For the below-the-coin arrangement, I’d use 20-gauge dead-soft copper wire around the stone, forming a secure loop at its upper end. Then I’d attach that loop to a small ring fixed to the bottom of the coin’s mounting.

I’d also consider a fixed connection rather than a freely swinging one. The stone is very sharp, and you don’t want it repeatedly striking the coin or swinging into your shirt.

One other detail: I’d mount the Sacagawea dollar in a coin bezel rather than soldering directly to it. That would preserve the coin and allow you to attach the bolo slide and the stone’s suspension ring to the bezel.

My question is whether you’re planning to show the Sacagawea portrait or the eagle side of the dollar. With the projectile point hanging below, the portrait side would make a particularly interesting historical pairing.

Your ideas are nice, but my projectile point is authentic and possibly prehistoric so it will be inside a wire cage. I’m thinking gold colored wire.

ChatGPT said:

Gold-colored wire would be an excellent choice, particularly with the Sacagawea dollar. It would tie the coin and the gray projectile point together visually, while allowing the stone’s unusual lighter band to stand out.

For your authentic 4 cm point, I’d recommend 20-gauge dead-soft gold-filled wire for the main cage, with 22-gauge wire for securing the framework.

There are three materials worth considering:

WireAdvantagesDisadvantages
Gold-filledDurable gold finish, attractiveExpensive
Gold-colored craft copperInexpensive, easy to shapeFinish may wear
Raw brassNaturally golden, inexpensive, durableTarnishes over time

My choice would be 20-gauge dead-soft brass wire, provided you’re comfortable with its tendency to develop a patina. It should look good alongside the Sacagawea coin, which itself has a manganese-brass outer layer.

I’d make a cage with two longitudinal wires running along the sides of the stone, connected by several short cross-wraps. The shoulders and stem would provide the primary retention points. That way, the sharp edges and the lighter band remain visible, and the wire doesn’t have to grip the stone with excessive pressure.

One thing I’d avoid is using the stone’s sharp tip as a structural anchor. An authentic artifact deserves a reversible mounting that doesn’t chip or abrade it.

I’m leaning toward having the stone dangle below the coin, with its point downward. That would give the bolo tie a natural vertical arrangement.

Can you mockup an image of the projectile point with a wire cage and the dollar?

Posted in

Leave a Reply